To view this in your browser click here.

IAPMO Uniform Codes Spotlight

If you have questions or comments, join the discussion on our LinkedIn forum.

From the 2015 UPC Illustrated Training Manual

901.2 Vents Required.
Each plumbing fixture trap, except as otherwise provided in this code, shall be protected against siphonage and backpressure, and air circulation shall be ensured throughout all parts of the drainage system by means of vent pipes installed in accordance with the requirements of this chapter and as otherwise required by this code.

This section requires that the fixture trap be protected against siphonage and backpressure by means of a vent system. The principle of ventilating the drainage system to retain trap seals has been the basis of modern plumbing systems since the end of the 19th century. Prior to the 20th century, plumbing fixtures were rarely used inside the building. The protection of the trap and its trap seal (see Figure 901.2a) by a vent has allowed the plumbing fixture to be placed safely inside the building (see also commentary for traps and trap protection in Sections 1001.2 and 1002.1). Without a vent, the trap seal is subject to siphonage or backpressure, which would allow sewer gas to enter the building or room. The consequences of sewer gas escaping the drainage system and entering the room can be lethal, as was proven in the SARS epidemic (Severe Acute Respiratory Syndrome) reported in Hong Kong, China in 2003, where 65 deaths and 321 infected people resulted from the virus being transmitted in part through dry traps.


Siphonage
Siphonage can occur in two ways. It occurs when there is sufficient negative pressure (aspiration or negative pressure below atmospheric) to draw water out of the fixture trap. A negative pressure occurs in a drainage stack as water rapidly flows downward, drawing air into itself (entrainment). If the sheet of water flows past an unvented branch connecting to the stack, a negative pressure will also be produced in the branch affecting any trap seals in the branch. If the negative pressure is great enough, then a siphon will occur. Also, a negative pressure occurs in the drain when a fixture is discharged. The discharging fixture may siphon an adjacent fixture trap that is not vented. For these reasons, venting is required to relieve any aspiration that may affect a trap seal.

Siphonage may also occur by a fixture siphoning itself at the end of its discharge. This is called self-siphonage. According to Recommended Minimum Requirements for Plumbing (BH13) published by the National Bureau of Standards (NBS), self-siphonage occurs when there is an unbalanced water column in an inverted U shape caused by the Ptrap as seen in the common siphon (see Figure 901.2b). Selfsiphonage is also caused by the fluid velocity, or the momentum pull exerted by the moving column of water, whether the pipe is horizontal, vertical, or inclined. In a horizontal drain from the trap, the momentum pull in its full intensity is exerted at the end of the discharge (see Figure 901.2c). Therefore, such configurations are prohibited without the fixture traps properly vented to prevent self-siphonage.

Backpressure
Backpressure occurs when there is positive air pressure (increase or positive pressure above atmospheric) in the drainage system. As water flows down a stack drawing air along with it, it also pushes air ahead of itself. The air volume will flow through the building drain and dissipate into the sewer drainage system unless there is a blockage in the air path, such as when the building drain is full, or when there is a building trap or a backwater valve. Such blockages in the air path generate positive pressures and may have an adverse effect on trap seals. This back pressure on the outlet side of the trap could push air bubbles through the trap way releasing sewer gas into the living space and, if significant enough, could even blow the water out of the trap way (see Figure 901.2d).

A particular blockage or closure in the air path is the hydraulic jump. A hydraulic jump is a flow condition where the flow rate becomes greater than the drain capacity causing the depth of the flow to be greater than the pipe diameter. This sudden rise is called a jump and may completely block air flow (see Figure 901.2e). Hydraulic jumps may occur at horizontal junctions where one branch flows into another and at the base of drainage stacks (see also commentary in Section 706.4). When the hydraulic jump completely fills the drain, positive air pressure waves will be generated, and if they last long enough then traps seals in close proximity may be affected. Backpressures generated by hydraulic jumps must be relieved by the venting system to protect trap seals.

Air Circulation
Section 901.2 also requires air circulation shall be ensured throughout all parts of the drainage system by means of vent pipes. This statement means that air must circulate throughout the drainage system including the building drain, building sewer, and public sewer. The basic principles of venting ensures that the equalization of atmospheric pressure on both sides of the trap seal within plus or minus one-inch water column, will be provided at all times and in all parts of the drainage system.

As already mentioned, building traps (see Figure 901.2f) block air circulation to the building drain and sewer and therefore are prohibited in Section 1008.1 except where allowed by the Authority Having Jurisdiction (AHJ). The reason the building trap is not used extensively in the Uniform Plumbing Code (UPC) is that the storm system is intended to be separate from the sewer system. Sewer manholes are sealed unlike storm system manholes and do not provide for air circulation in the sewer system. Therefore, the circulation of air for the public sewer, the building sewer and the building drainage system must come from the vents in the building alone. In Section 1008.1, the building trap is allowed but will require a relieving vent to provide for the circulation of air upstream of the building trap, and in Section 904.1 it will require another vent downstream of the building trap to allow circulation of air to the public sewer or private sewage disposal system.


The 2015 Uniform Plumbing Code Illustrated Training Manual eBook is available for purchase here.

© 2017 International Association of Plumbing and Mechanical Officials.
 
IAPMO website LinkedIn Twitter Facebook
 

You will continue to receive e-mail notifications from us until such time as you unsubscribe. To make sure these e-mails are not sent to your bulk or junk mail folders, add news@iapmo.org to your address book. Requests for new subscriptions or change of e-mail address should be sent to news@iapmo.org. IAPMO does not knowingly participate in SPAM. We do not sell, rent or trade the names on our e-mail list; your e-mail address is only used to send messages from IAPMO. If you wish to be removed from this list, follow the link below.

Click here to unsubscribe from the IAPMO mailing list

Facebooktwitteryoutubelinkedin

1-909-472-4100
news@iapmo.org
International Association of Plumbing
and Mechanical Officials
4755 E. Philadelphia St.
Ontario, CA 91761
Twitter LinkedIn